 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ISO-9001 CERTIFIED BY DSCC M.S.KENNEDY CORP. FEATURES: THREE PHASE BRIDGE MOSFET POWER MODULE 3017 (315) 701-6751 4707 Dey Road Liverpool, N.Y. 13088 All N-Channel Mosfets Isolated Package for Direct Heat Sinking, Excellent Thermal Conductivity Avalanche Rated Devices Interfaces with Most Brushless Motor Drive IC's 200 Volt, 30 Amp Full Three Phase Bridge at 25C DESCRIPTION: The MSK 3017 is an all N-Channel three phase power MOSFET Bridge Circuit. Packaged in a space efficient isolated ceramic tab power SIP that allows for direct heat sinking, the MSK 3017 can be interfaced with a wide array of brushless motor drive IC's. The MSK 3017 uses M.S Kennedy's proven power hybrid technology to produce a cost effective high performance circuit for use in today's sophisticated servo motor and disk drive systems. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS Three Phase Brushless DC Motor Servo Control Disk Drive Spindle Control Fin Actuator Control Az-El Antenna Control 1 2 3 4 5 6 7 8 9 10 1 1 1 PIN-OUT INFORMATION Drain Q2, Q4, Q6 Drain Q2, Q4, Q6 Drain Q2, Q4, Q6 Gate Q2 Gate Q1 Drain Q1, Source Q2 Drain Q1, Source Q2 Drain Q1, Source Q2 Gate Q4 Gate Q3 Drain Q3, Source Q4 12 13 14 15 16 17 18 19 20 21 Drain Q3,Source Q4 Drain Q3, Source Q4 Source Q1, Q3, Q5 Source Q1, Q3, Q5 Source Q1, Q3, Q5 Gate Q6 Drain Q5, Source Q6 Drain Q5, Source Q6 Drain Q5, Source Q6 Gate Q5 Rev. - 8/01 ABSOLUTE MAXIMUM RATINGS TJ TST TC TLD 1.0C/W 1.6C/W ELECTRICAL SPECIFICATIONS Parameter Drain-Source Breakdown Voltage Drain-Source Leakage Current Gate-Source Leakage Current Gate-Source Threshold Voltage Drain-Source On Resistance 2 Drain-Source On Resistance 3 Forward Transconductance 1 Total Gate Charge Gate-Drain Charge Turn-On Delay Time Rise Time Fall Time 1 1 1 1 1 Gate-Source Charge 1 Test Conditions 4 VGS=0 ID=0.25mA VDS=200V VGS=0V VGS=20V VDS=0 VDS=VGS ID=250A VGS=10V ID = 30A VGS=10V ID=30A VDS=50V ID=30A ID = 30A VDS=160V VGS = 10V VDD=100V ID = 30A RG = 4.3 RD = 2.1 VGS=0V VDS=25V f=1MHz IS=30 A VGS=0V IS=30 A di/dt=100A/S MSK3017 Min. 200 2.0 24 Typ. 23 120 100 94 5200 1200 310 1.8 390 4.8 Max. 250 100 4.0 0.09 0.06 230 42 110 590 7.2 Units V A nA V S nC nC nC nS nS nS nS pF pF pF V nS C Turn-Off Delay Time 1 Input Capacitance 1 Output Capacitance 1 Reverse Transfer Capacitance 1 Body Diode Forward On Voltage 1 Reverse Recovery Time 1 Reverse Recovery Charge 1 NOTES: 1 2 3 4 This parameter is guaranteed by design but need not be tested. Typical parameters are representative of actual device performance but are for reference only. Resistance as seen at package pins. Resistance for die only; use for thermal calculations. TA=25C unless otherwise specified. 2 20V MAX 30A MAX 46A MAX 200V MAX VDSS VDGDR Drain to Source Voltage Drain to Gate Voltage (RGS=1M) VGS Gate to Source Voltage (Continuous) ID Continuous Current IDM Pulsed Current RTH-JC Thermal Resistance (Junction to Case)@25C RTH-JC Thermal Resistance (Junction to Case)@125C 200V MAX Single Pulse Avalanche Energy 1000 mJ Junction Temperature +150C MAX Storage Temperature -55C to +150C Case Operating Temperature Range -55C to +125C Lead Temperature Range (10 Seconds) 300C MAX Rev. - 8/01 APPLICATION NOTES BRIDGE DRIVE CONSIDERATIONS It is important that the logic used to turn ON and OFF the various transistors allow sufficient "dead time" between a high side transistor and its low side transistor to make sure that at no time are they both ON. When they are, this is called "shoot-through", and it places a momentary short across the power supply. This overly stresses the transistors and causes excessive noise as well. See Figure 1. This deadtime should allow for the turn on and turn off time of the transistors, especially when slowing them down with gate resistors. This situation will be present when switching motor direction, or when sophisticated timing schemes are used for servo systems such as locked antiphase PWM'ing for high bandwidth operation. Figure 1 3 Rev. - 8/01 TYPICAL PERFORMANCE CURVES 4 Rev. - 8/01 MECHANICAL SPECIFICATIONS ALL DIMENSIONS ARE 0.010 INCHES UNLESS OTHERWISE LABELED. ORDERING INFORMATION Part Number MSK 3017 Screening Level Industrial 4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. M.S. Kennedy Corp. 5 Rev. - 8/01 |
Price & Availability of MSK3017
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |